Door Unit - Limited Warranty
DW Distribution Inc (“DW”) offers the following Limited Warranty on door units produced by DW after May 18, 2020
Terms and Conditions of the DW Limited Warranty:
DW warrants, subject to the terms and conditions below, that all components of its door units including slab, sills, frames, jambs, stop, hinges, brick mould and casing to be free from manufacturing defects in material and workmanship under normal conditions and use for the following periods from the date of delivery by DW to DW’s customer or the date of installation, provided that the installation occurs within 30 days of such delivery. DW will at its option repair or replace any defective door in the same condition as it was originally supplied. Cost incurred by the builder for rehanging, repainting or refinishing the door is not reimbursed by DW. Doors, jambs, trim or weather-stripping packages that have been altered from the original factory specifications will have all warranties voided. For a full description of a Manufacturer’s warranty, review their brochure or website for full explanation and/or exclusions of their warranty.
Interior Doors
Masonite Hollow Core Doors – 5 Years
Masonite Solid Core Doors – 7 Years
Masonite Stile and Rail Doors – 1 Year
Exterior Doors
Masonite Utility Steel Wood Edge Doors – 1 Year
Masonite High-Definition Steel Wood Edge Doors – 5 Years
Masonite Fiberglass Doors – Limited Lifetime Masonite Stile and Rail Doors – 1 Year
Masonite Torrified Stile and Rail Doors – 20 Years
SDL Bars – 1 Year
Door Glass Masonite Stile and Rail Insulated Glass – 5 Years Masonite Fiberglass and Steel Insulated Glass (Decorative and Mini Blinds) – 20 Years
Masonite Fiberglass and Steel Factory Finished PVC Glass – 5 Years (Frame) and 2 Years (Finish)
For the warranty to be valid, the following instructions below have to be observed:
- All products must be inspected at time of delivery. Any defects must be reported before painting, staining or otherwise altering the product. DW cannot be responsible for damage to glass that is not reported within 24 hours of delivery.
- All door and frame components must be finished and maintained in the strictest conformity with industry installation standards and finishing instructions provided with the product. Industry installation standards can be found in a number of places including:
- STM Standards in Building Codes, 4 Volume 43rd Edition, 2006
- 2003 International Building Codes – ISBN# 9041S03
- Association of Window and Door Installers
- American Window and Door Institute
- Installing & Hanging Doors (For Pros by Pros) ISBN# 1-56158-635-8
- www.fema.gov/pdf/rebuild/mat/fema499/hgcc_fact22.pdf
- All door units must be fully installed within 30 days of delivery and finished (all six sides) immediately upon installation.
- Door has to be handled carefully. They must be stored in a dry place away from heat.
- Door should be delivered to building site only after plaster, texture or cement is completely dry, and, if to be stored at building site for longer than one week, the entire door including top and bottom edges must be sealed with adequate resin or pigment base sealer or the equivalent.
- Structural strength or utility doors must not be impaired in fitting of the door or by application of the hardware.
- To prevent excessive moisture absorption which may results in warpage or delamination, the entire door including all edges must receive at least two coats of paint, varnish or the other properly applied sealer, which is in conformity to minimum commercial standards, immediately after fitting, beveling and cutting for latches, hinges, weather-stripping, thresholds or other hardware.
- Before finishing, door surfaces must be clean and dry, with a moisture content no higher than locally prevailing standards. Any marks, bruises, dust, stamps or labels must be removed by sanding before application of sealer or finish.
- Warping is considered a manufacturing defect if the warp exceeds 1/4”.
- Caution: Tempered glass scratches easily. We recommend a plastic scraper knife, not tools made of metal, such as razor blades, to clean glass.
- Powder Post Beetles: Since powder post beetles can exist in any hardwood product, regardless of preventative measures, DW disclaims any and all expressed or implied warranties on hardwood products. The purchase of hardwood product shall be at the total risk of the consumer.
- Damage caused by others or any cause outside the control of DW is not covered by this warranty. This includes damage caused by misuse, abuse, accident or mishandling. This includes installations without adequate overhang or an appropriate finish. Inadequate overhang is typically defined as an overhang projecting less than one-half the elevation distance between the bottom of the door and the base of the overhang. Dark finishes should be avoided, especially where a door is exposed to direct sunlight. DW at its sole discretion will determine the adequacy of the overhang or the appropriateness of the finish.
- Flush doors with ash face veneers, flush doors with two different face veneers and doors with cutouts that impair the structural integrity of the door are excluded from all warranties.
- Anyone other than the original retail consumer purchaser of the product.
- Purchasers for resale of door units.
- Improper delivery by anyone other than DW, improper storage, improper installation, improper or unauthorized repair, improper maintenance, improper protection, improper care, abuse, water, moisture, insects, animals, and any other condition beyond our control.
- Any defect that was observable before installation.
- Natural wood characteristics such as, but not limited to, mineral streaks, small knots, grain, texture, color, and tone variations.
- Differences between samples or photographs and the actual door unit.
- Natural expansion and contraction during seasonal and temperature changes, air conditioning or heating influences.
- Warp in plane of door less than 1/4”.
- Any improper job site condition or any inappropriate or improperly prepared framing, sill, supporting or adjacent area of the door unit.
- Installation of door units outside the continental United States.
- Damage caused by failure to comply strictly with industry installation standards and finishing instructions.
- Damage caused by anyone other than DW repairing or altering the door unit.
- Accidents, man-made or natural, including but not limited to leaking or broken plumbing, fire, flood, earthquake or other casualty before, during or after installation.
- Settling of the building.
- Indentations, scratches or similar surface damage caused by negligence, lack of protection, improper maintenance, normal use, abrasives, insufficient protection, pets or other conditions.
- Excessive or inadequate humidity in the area or excessive change in ambient temperature.
- Damage caused by failure to perform yearly inspections and maintenance.
- Any other condition, circumstance, event or conduct beyond our control.